View BIR-HO033A-TRB_4129026.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BIR-HO033A-TRB
Features:
1. Lens Appearance : Water Clear. 2. 3.2x1.6x1.4mm(1206) standard package. 3. Suitable for all SMT assembly methods. 4. Compatible with infrared and vapor phase reflow solder process. 5. Compatible with automatic placement equipment. 6. This product doesn't contain restriction Substance, comply ROHS standard.
Package Dimensions:
Applications:
1. Remote Control. NOTES: 1.All dimensions are in millimeters (inches). 2.Tolerance is 0.10mm (0.004") unless otherwise specified. 3.Specifications are subject to change without notice. 4.Lead Spacing is measured where the leads emerge from the package. 2. Smoke Detector 3. Phtoto Detector 4. Automatic Control System
Absolute Maximum Ratings(Ta=25)
Parameter
Power Dissipation Forward Current Peak Forward Current 1 Reverse Volage Operating Temperature Storage Temperature Soldering Temperature
Symbol
Pd IF IFP VR Topr Tstg Tsol
Rating
100 50 500 5 -25~80 -30~85 See Page6
Unit
mW mA mA V -
1 Pulse With = 10us, 1%Duty Cycle
Ver.1.0 Page 1 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BIR-HO033A-TRB
Electrical and optical characteristics(Ta=25) Parameter
Radiant Intensity Forward Voltage Peak Wave Length Spectral Line Half-width Rise/Fall Time Viewing Angle
Symbol
Ie VF p Tr Tf 21/2
Condition
IF=50mA IF=50mA IF=20mA IF=20mA Ifp=20mA PW=10uS DC=1% IF=20mA
Min.
1.83 -
Typ.
3.8 1.3 850 50 500 200 70
Max.
1.8 -
Unit
/sr V nm nm ns deg
Typical Electro-Optical sensitivity vs wavelength Characteristics Curves Fig.1 Relative spectral
1.0
Fig.2 Total power dissipation vs ambient temperature
60
50 Total power dissipation mW
Relative Spectral Sensltivty
40
0.5
30
20
10
0
800
850
900
0
20
40
60
80
100
Wavelength (nm)
Ambient temperature
Fig.3 Forward current vs forward voltage
50
Fig.4 RELATIVE LUMINOUS INTENSITY VS. AMBIENT TEMPERATURE
3.0
40 RELATIVE RADIANT POWER (NORMALIZED AT 20mA) 1 2 3 4 5
2.5
2.0
Forward current (mA)
30
1.5
20
1.0
10
0.5
0
0 -40
-20
0
20
40
60
Forward voltage(v)
AMBIENT TEMPERATURE Ta( C) A
Fig.5 Relative luminous intensity vs forward current
4.0 RELATIVE RADIANT POWER(@20mA)
RADIATION DIAGRAM
0 10 20 30
3.0
RELATIVE RADIANT INTENSITY
40
2.0
50 60 70 80 90 0.5 0.3 0.1 0.2 0.4 0.6
1.0
0
10
20
30
40
50
Forward current (mA)
Ver.1.0 Page 2 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BIR-HO033A-TRB
Tapping and packaging specifications(Units: mm)
Anode
USER DIRECTION OF FEED
1.46 0.1
START
13.0 0.5
1.98 0.1
END
71.0 1
13.0 0.5
5.3 0.05
3.5 0.05
8.0 0.3
3.47 0.1
TRAILER
Cathode
1.75 0.1
4.0 0.1 4.0 0.1
1.5 0.1 2.0 0.05
LEADER 0.3 FIXING TAPE
NOTE: 3000 pcs PER REEL
Package Method:(unit:mm)
12 bag/box 3000 pcs/reel
200
Bar Code Label
245 220 185
220
Aluminum Foil Bag
645
6 box/carton
210 470
Ver.1.0 Page 3 of 7
179 1
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BIR-HO033A-TRB
Bin Limits I n t e n s i t y B i n L i m i ts ( A t 5 0 m A ) BIN CODE Min. (mcd)
6 7 8 9 1.55 2.18 3.06 4.29
Max. (mcd)
2.95 4.14 5.80 8.13
B IN x
Intensity BIN CODE
Ver.1.0 Page 4 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BIR-HO033A-TRB
Reliability Test Test Item Reference Standard Operation Life MIL-STD-750:1026 MIL-STD-883:1005 JIS C 7021 :B-1 High Temperature MIL-STD-202:103B High Humidity JIS C 7021 :B-11 Endurance Storage Test High MIL-STD-883:1008 Temperature JIS C 7021 :B-10 Storage Low Temperature JIS-C-7021 :B-12 Storage Temperature MIL-STD-202:107D Cycling MIL-STD-750:1051 MIL-STD-883:1010 JIS C 7021 :A-4 Thermal Shock MIL-STD-202:107D Environmental MIL-STD-750:1051 Test MIL-STD-883:1011 Solder MIL-STD-202:201A Resistance MIL-STD-750:2031 JIS C 7021 :A-1 Classification Test Conditions Connect with a power If=50mA Ta=Under room temperature Test time=1,000hrs Ta=+655 RH=90%-95% Test time=240hrs High Ta=+855 Test time=1,000hrs Low Ta=-355 Test time=1,000hrs -35 ~ +25 ~ +85 ~ +25 60min 20min 60min 20min Test Time=5cycle -355 ~ +855 20min 20min Test Time=10cycle Preheating 140-160,within 2 minutes. Operation heating 260(Max.), within 10seconds. (Max.) Result 0/20
0/20
0/20
0/20
0/20
0/20
0/20
Judgment criteria of failure for the reliability Measuring items Collector Dark Current Collector Light Current Note: Symbol Id ISC Measuring conditions VCE=20V, H=1.0 mW/cm2 VCE= 5V, H=1.0 mW/cm2 Judgment criteria for failure Over Ux2 Below SX0.5
1.U means the upper limit of specified characteristics.
S means initial value.
2.Measurment shall be taken between 2 hours and after the test pieces have been returned to normal ambient conditions after completion of each test.
Ver.1.0 Page 5 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BIR-HO033A-TRB
Soldering :
1. Manual Of Soldering The temperature of the iron tip should not be higher than 300(572) and Soldering within 3 seconds per solder-land is to be observed. 2. Reflow Soldering Preheating : 140~1605,within 2 minutes. Operation heating : 260(Max.) within 10 seconds.(Max) Gradual Cooling (Avoid quenching).
10 SEC. MAX.
3. DIP soldering (Wave Soldering) : Preheating : 120~150,within 120~180 sec. Operation heating : 2455 within 5 sec.260 (Max) Gradual Cooling (Avoid quenching).
Handling :
Care must be taken not to cause to the epoxy resin portion of BRIGHT LEDs while it is exposed to high temperature. Care must be taken not rub the epoxy resin portion of BRIGHT LEDs with hard or sharp article such as the sand blast and the metal hook.
Temperature
140~160
260 MAX. 4 /SEC. MAX.
4 /SEC. MAX. OVER 2 MIN.
Time
Soldering heat Max. 260 120~150 245 5 within 5 sec.
Temperature
Preheat 120~180 sec.
Time
Ver.1.0 Page 6 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BIR-HO033A-TRB
Notes for designing:
Care must be taken to provide the current limiting resistor in the circuit so as to drive the BRIGHT LEDs within the rated figures. Also, caution should be taken not to overload BRIGHT LEDs with instantaneous voltage at the turning ON and OFF of the circuit. When using the pulse drive care must be taken to keep the average current within the rated figures. Also, the circuit should be designed so as be subjected to reverse voltage when turning off the BRIGHT LEDs.
Storage:
In order to avoid the absorption of moisture, it is recommended to solder BRIGHT LEDs as soon as possible after unpacking the sealed envelope. If the envelope is still packed, to store it in the environment as following: (1) Temperature : 5-30(41)Humidity : RH 60Max. (2) After this bag is opened, devices that will be applied to infrared reflow, vapor-phase reflow, or equivalent soldering process must be: a. Completed within 24 hours. b. Stored at less than 30% RH. (3) Devices require baking before mounting, if: (2) a or (2) b is not met. (4) If baking is required, devices must be baked under below conditions: 12 hours at 603.
Package and Label of Products:
(1) Package: Products are packed in one bag of 3000 pcs (one taping reel) and a label is attached on each bag. (2) Label:
BRIGHT LED LOGO Part No. Quantity BIN. Sealing Date x xx xx Year Month xx Day
Manufacture Location
Ver.1.0 Page 7 of 7

▲Up To Search▲

Price & Availability of BIR-HO033A-TRB

	To Download BIR-HO033A-TRB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .